Behaviors of concrete-filled steel tubular members subjected to combined loading

The present study is an investigation on the behaviors of concrete-filled thin-walled steel tubular members subjected to combined loading, such as compression and torsion, bending and torsion, compression, bending and torsion. ABAQUS software is used in this paper for the finite element analysis (FEA). A comparison of results calculated using this modeling shows generally good agreement with test results. The FEA modeling is then used to investigate the influence of important parameters that determine the ultimate strength of the composite members under combined loading, such as compression and torsion, bending and torsion, compression, bending and torsion. The parametric studies provide information for the development of formulae for calculating the ultimate strength of the composite members subjected to combined loading.     

Clay compaction modelling by homogenization theory

The modelling of hydromechanical behavior of clayey sediments by homogenization theory is described. The rheological model of clays buried in depth requires a three-dimensional approach and laboratory experiments to quantify the model parameters. An iterative process which can be coupled to any homogenization method is used to model the porous media behavior. Hydromechanical compaction results from oedometric experiments are simulated with the proposed model.     

Research on Marine Boiler＇s Pressurized Combustion and Heat Transfer

The effect of pressure on combustion and heat transfer is analyzed. The research is based on the basic combustion and heat transfer theorem. A correction for the heat calculation method for pressurized furnace is made on the basis of the normal pressure case. The correction takes the effect of pressurizing into account. The results show that the correction is reasonable and the method is applicable to combustion and heat transfer of the marine supercharged boiler.     

Sol-Gel Preparation of LaNiO3 and Its Physical and Chemical Properties

LaNiO3 was synthesized by sol-gel method in which lanthanum nitrate and nickel nitrate were used as start materials and citric acid was used as complex for gel formation.The precursor was dried and subsequently heated at elevated temperature to form the desired product.XRD analysis shows that pure LaNiO3 was synthesized.Electrical conductivity and electrochemical performance of the material were tested.The electrical conductivity decreases from 34.5that there are current peaks in the curve, which is the evidence of the electrochemical activity of LaNiO3.     

直流法测量钯氢化物电极电阻时的阻值偏移

讨论了直流法在线测量钯氢化物电极电阻时的电化学效应，计算了电解液的共导、测量电流与电解电流引起的浓差电池效应以及电极作为集流体引起的电阻贡献。结果表明：当电极具有高的长度与半径比值、粗糙的表面、高的溶液电导以及大的电解电流时容易引起显著的附加电阻。     

Three dimensional boundary element analysis of internal cracks under sliding contact load with a spherical indenter

Using boundary element based three dimensional modelling for linear fracture mechanics, we present an analysis of cracking in a homogeneous medium subject to contact load. The proposed iterative solution procedure allows a simultaneous treatment of a reasonable number of partially closed cracks. It is shown that the most probable direction of propagation of a vertical internal crack is strongly dependent on its size compared to the contact radius and its location with respect to the axis of maximum normal load.     

Boiling: Size Distribution of Bubbles as Demanded by the Principle of Maximum Information

The principle of maximum informational entropy is used to find the probability density function for the departure radius of a bubble in boiling on a solid surface. A general relation is derived, which leads to particular expressions.     

A direct stiffness analysis of a composite beam with partial interaction

The use of the conventional semi-analytical stiffness method in finite element analysis, in which interpolation polynomials are used to develop the stiffness relationships, leads to problems of curvature locking when beam-type elements are developed for composite members with partial interaction between the materials of which it is comprised. The curvature locking phenomenon that occurs for composite steel–concrete members is quite well reported, and the general approach to minimizing the undesirable ramifications of curvature locking has been to use higher-order polynomials with increasing numbers of internal nodes. This paper presents an alternate formulation based on a direct stiffness approach rather than starting from pre-defined interpolation polynomials, and which does not possess the undesirable locking characteristics. The formulation is based on a more general approach for a bi-material composite flexural member, whose constituent materials are joined by elastic shear connection so as to provide partial interaction. The stiffness relationships are derived, and these are applied to a simply supported and a continuous steel–concrete composite beam to demonstrate the efficacy of the method, and in particular its ability to model accurately both very flexible and very stiff shear connection that causes difficulties when implemented in competitive semi-analytical algorithms. Copyright © 2004 John Wiley & Sons, Ltd.     

Application of piece‐wise linear weight functions for 2D 8‐node quadrilateral element in contact problems

The present study is a continuation of our previous work with the aim to reduce problems caused by standard higher order elements in contact problems. The difficulties can be attributed to the inherent property of the Galerkin method which gives uneven distributions of nodal forces resulting in oscillating contact pressures. The proposed remedy is use of piece‐wise linear weight functions. The methods to establish stiffness and/or mass matrix for 8‐node quadrilateral element in 2D are presented, i.e. the condensing and direct procedures. The energy and nodal displacement error norms are also checked to establish the convergence ratio. Interpretation of calculated contact pressures is discussed. Two new 2D 8‐node quadrilateral elements, QUAD8C and QUAD8D, are derived and tested in many examples, which show their good performance in contact problems. Copyright © 2004 John Wiley & Sons, Ltd.     

Constitutive modelling and numerical simulation of multivariant phase transformation in superelastic shape‐memory alloys

This work concerns the micromechanical constitutive modelling, algorithmic implementation and numerical simulation of polycrystalline superelastic alloys under multiaxial loading. The model is formulated in finite deformations and incorporates the effect of texture. The numerical implementation is based on the constrained minimization of the Helmholtz free energy with dissipation. Simulations are conducted for thin tubes of Nitinol under tension–torsion, as well as for a simplified model of a biomedical stent. Copyright © 2004 John Wiley & Sons, Ltd.